Packing support grid, metal grid, plastic grid, PP grid plate, customized by manufacturer

Description :

　　Packing support grid, metal grid, plastic grid, PP grid plate, customized by manufacturer

　　The packing support grid produced by our company is determined based on the following factors: tower diameter, tower body ellipticity, grave material diameter, material layer height, grid plate processing, manufacturing, and installation and disassembly. Due to the smaller diameter of the tower, a single block grid plate is used. When the tower diameter is less than 350mm, the grid plate can be directly welded to the tower wall. When the tower diameter is between 400-500mm, the grid plate needs to be placed on the support welded to the tower wall. When the diameter is large, it is advisable to use segmented grid plates. When the tower diameter is between 600-800mn, the grid plate consists of two pieces When the tower diameter is 900-1200mm, the grid plate consists of three pieces. When the tower diameter is between 1400-1600mm, the grid plate consists of four pieces. But regardless of how many pieces the grid plate is divided into, it needs to be attached to the supports or support blocks welded to the tower wall. The supports of large towers also need to be reinforced with support plates. The grating is divided into blocks based on the manhole of the equipment.

　　The packing support grid is mainly used in corrugated packing towers and bulk packing towers. In various chemical and environmental equipment, packing towers are used as packing supports. In the process of oil gas water separation in crude oil three-phase separators, corrugated plates are used to aggregate packing for side and bottom support. In sulfuric acid absorption towers, drying towers, and cooling towers, ceramic cross rings are added to acid resistant ceramic grids, followed by bulk granular packing on top. Placing a plate of corrugated packing on the grid support is also a good method, which not only increases the opening rate of the support device, but also increases the spacing between the grid bars to over 100mm. Some of them have sawtooth grooves at the lower end of the grid Flat noodles, which can make the liquid flow down easily and evenly.

　　Filler support grid is a structurally simple and commonly used filler support device. It is placed on the support ring welded. Cast iron support grating has been widely used in the chlor alkali and sulfuric acid industries for a long time. However, when filling bulk packing, the enlarged cross diaphragm ring can be placed on the grid Flat noodles for filling, and its size and specification depend on the type of packing in the tower. If the filling inside the tower is too small, several layers should be placed and the size should be gradually reduced to prevent the scattered packing from falling off. This can also increase the distance between the grid plates, saving materials and processing time.

　　In September 2020, a customer from Shanxi ordered 3 sets of 2.6-meter 316L filler grid fillers from our company. Our company produced and shipped them according to the customer's requirements. The product quality and service have been recognized by customers.

　　Dier Chemical Packing is used to produce packing materials for petrochemical equipment and environmental protection equipment;

　　Plastic loose packing: Ball ring, stepped ring, saddle ring, conjugate ring, Rascal ring, flower wreath, polyhedral hollow ball, floating ball, plastic snowflake ringEnvironmental BallAlpha ring, Laru ring, three combinations of one filler, etc;

　　The above finished products are made of materials such as PP/PVC/CPVC/PVDF/PTFE/flame retardant materials, etc

　　Metal loose packing materials: Ball rings, stepped rings, saddle rings, conjugate rings, Raschig rings, Entrox rings, aluminum flower garlands, 84 inner arc rings, flat rings, double-layer conjugate rings, etc.

　　The above finished products are made of materials such as 304/304L/316/316L/duplex steel/urea grade stainless steel, etc

　　Ceramic bulk packing: Ball ring, stepped ring, saddle ring, conjugate ring, Rascal ring, cross partition ring, etc.

　　Regular packing: plastic/metal/ceramic orifice plate corrugated, perforated corrugated and wire mesh corrugated packing, etc.

　　Tower internals packing: trough distributor, trough distributor, tubular distributor, hump support, bubble cover tray, fog catcher, wire mesh demister, wavy wire mesh demister, grid packing, support, pressure grid, clamp, gasket, etc;

　　Dier Chemical Packing Co., Ltd. in Pingxiang City, Jiangxi Province can produce various products according to customer needs and provide a comprehensive system of design, production, and installation services; Please consult the sales department for details;

AfterSalesService :

• Filler supported grid