Huaihua Traffic Sign Single Suspension Pole Processing Factory One stop Service

Description :

　　The rolling structure ratio of Huaihua cold-rolled aluminum plate is higher and the strength is better than that of hot-rolled aluminum alloy plate. Anodizing on the surface of the aluminum plate slightly reduces the strength. The difference between the two lies in the supply of raw materials. Hot rolled billets are made by casting aluminum ingots, heating, and rolling

　　More than ten years of production experience, focusing on quality

　　18 years of experience in producing outdoor billboards and tens of thousands of engineering practices;

　　Our company's sales coverage covers over 85% of cities nationwide and has received high praise from customers;

　　High quality materials, excellent craftsmanship, and superior quality

　　1. High quality aluminum and steel are selected for highway signs;

　　2. Strictly follow the national standard GB 5769.2-2009 for production;

　　Craftsmen with over 10 years of experience, independently mold making, and exquisite craftsmanship.

　　Mass production manufacturer for transportation engineering

　　1. Serving over 1000 transportation facility manufacturers;

　　2. Manufacturers of traffic signs, manufacturers sell them, saving intermediary fees;

　　3. Traffic signs offer high cost-effectiveness, and we welcome you to compare prices from three different sources.

　　Our company's project has covered all counties and towns in Huaihua City, and we provide free technical guidance. Huaihua Road Traffic Sign Manufacturer, Huaihua Traffic Sign Production, Huaihua Road Sign Pole Processing, Huaihua Traffic Sign Pole, Huaihua Scenic Area Sign Manufacturer, Huaihua Tourist Scenic Area Sign Manufacturer, Huaihua Traffic Sign Production Manufacturer, Huaihua Traffic Sign Manufacturer, Huaihua Traffic Safety Sign Manufacturer, Huaihua Safety Warning Sign Manufacturer, Huaihua Traffic Sign Pole Customization, Huaihua Hot Dip Galvanized Traffic Sign Pole Manufacturer, Huaihua Multi pole Traffic Sign Pole, Huaihua Expressway Sign Manufacturer

　　Installation method of road signs

　　1. The quality of all traffic sign components transported to the construction site shall comply with relevant technical standards and be approved by the supervising engineer before use;

　　2. After arriving at the site, make full use of safety facilities such as signs and road barriers to manage pedestrians and traffic, and strictly follow the operating rules for construction to ensure the safety of pedestrians and operators, prevent accidents as much as possible, and ensure construction safety;

　　3. Strictly follow the requirements of the construction drawings and determine the location of the signs based on the direction of traffic flow;

　　4. After determining the foundation position, excavate the foundation according to the dimensions specified in the design drawing, and process it according to the regulations. Then, erect the formwork, tie the steel bars, pour the concrete, and ensure that the position of the anchor bolts and base flanges is correct and reaches the specified elevation;

　　The installation of the sign support structure should be carried out after the strength of the foundation concrete meets the requirements and is approved by the supervising engineer. The flange of the pillar and the base flange of the concrete foundation should be level and tightly fitted, and the anchor bolts should be properly matched. After tightening the bolts, the pillar should not tilt;

　　6. Fix the signboard on the pillar by sliding bolts, clamps and other connecting accessories; The distance between the inner edge of the sign board of the column sign and the edge of the road shoulder should be ensured to be 20cm, the height of the lower edge of the single column sign board from the road surface should be ensured to be 250cm, and the clearance for cantilever installation should be ensured to be 5.2m from the road surface;

　　7. After installing the signboard, the verticality and height of the signboard should be checked and adjusted to meet the specified requirements;

　　8. When installing cantilever signs, the sign panel should be perpendicular to the centerline of the road. When installing roadside column signs, the sign panel should be as perpendicular or angled as possible to the centerline of the road: guidance and warning signs should be at an angle of 0-10 degrees, prohibition and indication signs should be at an angle of 0-45 degrees, and sight guidance signs should be at an angle of 80-90 degrees;

　　After the installation of the signboard is completed, all signboards should be cleaned to keep the layout clean.

　　Huaihua Traffic Sign Single Suspension Pole Processing Factory provides one-stop service. Closing is prohibited, and there are people working on the line! Size: and 80 * 65 Color: white background, red circular slash, black prohibition symbol, no disconnection allowed

　　Huaihua Traffic Sign Single Suspension Pole Processing Factory One stop Service

　　Signboards shall not be placed on movable objects such as doors, windows, and shelves. There shall be no fixed obstacles in front of or near warning signs that obstruct people's reading attempts, and efforts shall be made to avoid being frequently obstructed by other temporary objects. Signboards should be placed in a bright and well lit environment. For example, if the location where the signboard should be placed has additional dim light, auxiliary light sources should be considered. When multiple signboards are arranged together, they should be arranged in the order of warning, prohibition, instruction, and prompt types, from left to right, and from top to bottom. The distance between each signboard should be at least 0.2 times the size of the signboard

　　Next:

AfterSalesService :

• traffic sign