Lincang traffic sign manufacturer, identification sign manufacturer, saves money and worries

Description :

　　Lincang

　　Bus First Encounter: This means that the car can drive first when it encounters a small car, in order to give up its seat. When the car encounters a small car, it is necessary to slow down and let the other side of the car drive first. These two signs are integrated and applied together. They are located on both sides of a narrow road, where there are difficulties with buses. People only need to remember that the bright red arrow symbol means parking and giving up their seat

　　More than ten years of production experience, focusing on quality

　　18 years of experience in producing outdoor billboards and tens of thousands of engineering practices;

　　Our company's sales coverage covers over 85% of cities nationwide and has received high praise from customers;

Traffic sign manufacturerManufacturers of identification signs save money and effort

　　High quality materials, excellent craftsmanship, and superior quality

　　1. High quality aluminum and steel are selected for highway signs;

　　2. Strictly follow the national standard GB 5769.2-2009 for production;

　　Craftsmen with over 10 years of experience, independently mold making, and exquisite craftsmanship.

　　Mass production manufacturer for transportation engineering

　　1. Serving over 1000 transportation facility manufacturers;

　　2. Manufacturers of traffic signs, manufacturers sell them, saving intermediary fees;

　　3. Traffic signs offer high cost-effectiveness, and we welcome you to compare prices from three different sources.

　　Our company's project has covered all counties and towns in Lincang city, and we provide free technical guidance. Lincang Road Traffic Sign Manufacturer, Lincang Traffic Sign Production, Lincang Road Sign Pole Processing, Lincang Traffic Sign Pole, Lincang Scenic Area Indication Sign Manufacturer, Lincang Tourist Scenic Area Identification Sign Manufacturer, Lincang Traffic Sign Production Manufacturer, Lincang Traffic Sign Manufacturer, Lincang Traffic Safety Sign Manufacturer, Lincang Safety Warning Sign Manufacturer, Lincang Traffic Sign Pole Customization, Lincang Hot Dip Galvanized Traffic Sign Pole Manufacturer, Lincang Multi pole Traffic Sign Pole, Lincang Expressway Sign Label Manufacturer

　　Installation method of road signs

　　1. The quality of all traffic sign components transported to the construction site shall comply with relevant technical standards and be approved by the supervising engineer before use;

　　2. After arriving at the site, make full use of safety facilities such as signs and road barriers to manage pedestrians and traffic, and strictly follow the operating rules for construction to ensure the safety of pedestrians and operators, prevent accidents as much as possible, and ensure construction safety;

　　3. Strictly follow the requirements of the construction drawings and determine the location of the signs based on the direction of traffic flow;

　　4. After determining the foundation position, excavate the foundation according to the dimensions specified in the design drawing, and process it according to the regulations. Then, erect the formwork, tie the steel bars, pour the concrete, and ensure that the position of the anchor bolts and base flanges is correct and reaches the specified elevation;

　　The installation of the sign support structure should be carried out after the strength of the foundation concrete meets the requirements and is approved by the supervising engineer. The flange of the pillar and the base flange of the concrete foundation should be level and tightly fitted, and the anchor bolts should be properly matched. After tightening the bolts, the pillar should not tilt;

　　6. Fix the signboard on the pillar by sliding bolts, clamps and other connecting accessories; The distance between the inner edge of the sign board of the column sign and the edge of the road shoulder should be ensured to be 20cm, the height of the lower edge of the single column sign board from the road surface should be ensured to be 250cm, and the clearance for cantilever installation should be ensured to be 5.2m from the road surface;

　　7. After installing the signboard, the verticality and height of the signboard should be checked and adjusted to meet the specified requirements;

　　8. When installing cantilever signs, the sign panel should be perpendicular to the centerline of the road. When installing roadside column signs, the sign panel should be as perpendicular or angled as possible to the centerline of the road: guidance and warning signs should be at an angle of 0-10 degrees, prohibition and indication signs should be at an angle of 0-45 degrees, and sight guidance signs should be at an angle of 80-90 degrees;

　　After the installation of the signboard is completed, all signboards should be cleaned to keep the layout clean.

　　Lincang traffic sign manufacturer, identification sign manufacturer, saves money and worries

　　For highway sign posts, they can meet the needs of lighting and have a wider monitoring perspective. As an important guarantee for road safety and a crucial means of pursuing offenders, it is important to ensure that monitoring data is more accurate. Generally, a speed of 45m/s is required; For the process requirements of the sign pole, it should be polished smooth and welded firmly. The sign pole manufacturer also requires the road sign pole to have the ability to adapt to altitude, temperature difference and other performance. Choosing a more suitable road sign pole is important, and the price guarantee is obtained. Of course, we also see that the quotation of 6m road sign pole is relatively reasonable. According to the quotation of different manufacturers, the reliability it can bring will be better, and the sought reliability will have more outstanding performance. The sought benefits are very good. For the surface treatment of road sign poles, good rust prevention ability is required. Of course, there are special requirements for highway sign poles; Appearance requirements include equal diameter, conical shape, and variable diameter; The wind resistance ability should also be very superior

　　Lincang traffic sign manufacturer, identification sign manufacturer, saves money and worries

　　Traffic sign painting: The color of the product busbar should meet the requirements, and the painting should be uniform, without defects such as flow marks, brush marks, bubbles, wrinkles, and leaks. The overlapping surface should not stick to the paint, and special attention should be paid to the edges and corners when spraying the primer. Due to the weak and easily corroded edges and corners of the coated object, and the existence of dead corners that are difficult to spray, these parts of the coating should be strengthened. The primer layer must be dried moderately before repainting. If it is too dry, the primer layer is easily bitten by some topcoats; Excessive drying can lead to poor adhesion with the topcoat and the formation of shrinkage pores and "fermentation". In addition, be careful not to contaminate the workpiece after completing the primer

　　Next:

AfterSalesService :

• Traffic sign manufacturer