Dust collector single pulse dust removal equipment MC cyclone filter cartridge dust removal environmental protection equipment dust collector

Description :

Dust collector single pulse dust removal equipment MC cyclone filter cartridge dust removal environmental protection equipment dust collector

pulseDust collectorPerformance selection

　　1. The main technical parameters for selecting a dust collector are air volume, gas temperature, dust temperature, dust concentration, and humidity. According to the maximum values of air volume, gas temperature, and dust concentration in the process design, based on the principle of slightly smaller values than those in the technical performance table, the corresponding dust collector model is the required dust collector model.

　　2. The gas consumption in the table refers to the situation when the enterprise supplies gas centrally. If an air compressor is used separately, the gas consumption in the table should be increased to 1.5 times. In the compressed air consumption column, the proposed air consumption is the maximum air consumption of the equipment model.

　　3. The external dimensions of the equipment are shown in the attached diagram and size table. We can also design dust collectors that meet the user's requirements based on the on-site site conditions.

　　6、 Operation and Instructions

　　1. Before putting the equipment into use, the fan on the equipment should be checked for normal operation, abnormal noise or poor conditions, otherwise it should be shut down for repair. Check if the electromagnetic pulse valve is working properly and if the compressed air is at 0.5-0.7MPa, otherwise make adjustments.

　　2. Adjustment of pulse automatic dust cleaning. Read the user manual of the pulse controller carefully and adjust the pulse interval and pulse width. The adjustment of the pulse interval depends on the size of the dust volume. Generally, it can be set at around 10 seconds, and the pulse width can be set at around 0.1 seconds.

　　3. The dust stored in the ash collection cylinder should be cleaned regularly and periodically.

　　4. After the equipment is running, the dust collection effect of the equipment should be visually monitored. If obvious dust is found flying out of the clean air outlet, it indicates that the filter cartridge in the dust collector is loose or damaged, and should be checked and replaced in a timely manner. The filter cartridge needs to be cleaned for six months. The cleaning method is to carefully remove the filter cartridge, rinse it with clean water, and let it dry. It should not collide with hard objects to prevent scratching the filter material and reducing the dust collection effect. The disassembly of the filter cartridge should be carried out according to the "replacement method".

Special dust collector for denture polishingThe selection should be based on reliable quality, functional applicability, and easy operation. In addition to understanding the structure and power, it is also necessary to consider the number of additional functions, mainly based on the following seven points:

　　1. Power supply device: Power supply devices can be divided into wired and wireless according to the situation

　　2. Warranty period for industrial vacuum cleaners: Good quality ones will definitely have a warranty of more than 2 years, while poor quality ones usually only have a warranty of one year.

　　3. The quality of the grinder dust collection cabinet can be roughly judged from the appearance of the plastic parts, in addition to the origin and brand. Products with poor appearance generally have poor quality. The internal quality can be judged from aspects such as click noise level and air suction strength. During inspection, attention should also be paid to whether there is any air leakage at the hose and interface, and whether the accessories and spare parts are complete.

　　4. The capacity of the vacuum cleaner (usually 15 liters for office use and 60 liters for industrial use, choose the appropriate capacity)

　　5. Grinding machine dust collection cabinet force (When choosing a vacuum cleaner, you first need to know where you use it, what it mainly sucks, whether the particles are large or small, and the suction power of the vacuum cleaner is the key)

　　6. Is it convenient to clean dust? Industrial vacuum cleaners generally have two types of debris. 1、 External dust collection refers to central type; 2、 Internal dust collection bucket type, selected according to different customers.

Dust collector single pulse dust removal equipment MC cyclone filter cartridge dust removal environmental protection equipment dust collector

Pulse dust collectorComprehensive selection suggestions: 1. As a small hand grinder, flat grinder, tool grinder and other small grinding machines, if it is only fine grinding or dry grinding, it is recommended to use this vacuum cleaner. Firstly, it has low power, simple dust collection method, economy, environmental friendliness, and low noise.

　　2. As a larger precision grinder or inner and outer circular grinder, in addition to dehumidification grinding, consider using a 750W or higher power vacuum cleaner as much as possible, first considering the dust collection capacity and work efficiency, and single machine configuration.

　　3. If there is a combination of grinding fluid and workpiece during the precision grinding process, a 750W wet dry dual-purpose dust collector or a higher-level power vacuum cleaner must be selected. 4. Factors affecting the effectiveness of grinding machine vacuum cleaners: 1 Generally, in practical use, the suction power of industrial vacuum cleaners should be determined based on the weight and density of the waste being sucked in. When suctioning heavier particles, it is necessary to consider the diameter and length of the connecting pipe. The main factors that usually affect the suction effect are: too thick pipe diameter, too long pipe diameter, too low power of the suction fan itself, too many bends connected, and poor grading treatment! 3. Improper selection of the matching vacuum hood and improper design of the vacuum air outlet both affect the effectiveness of the vacuum cleaner. A commonly used equipment in industry, used for collecting waste, filtering and purifying air, and cleaning the environment during industrial production processes. Widely used in the textile and chemical industries, it can prevent the hazards of some occupational diseases.

Industrial dust collectorPrecautions for use:

　　During use, it should be managed by a dedicated person as much as possible. For first-time use, check whether the filter bag and filter element are installed properly, check the direction of the fan, and for those using belt transmission, check whether the belt has fallen off. After each use, try to clean the dust in the filter bag as much as possible to prevent moisture adhesion, which is not conducive to filtration and can easily damage the filter bag. Before use, check whether the filter bag and filter element are damaged. If they are damaged, the industrial vacuum cleaner should be replaced in a timely manner. It is strictly prohibited to use damaged filter bags and filters. If the suction force decreases during use, it is necessary to check whether the vacuum tube and suction head are blocked, whether the filter bag is too full, and whether there is too much dust on the surface of the filter element. Depending on the amount of dust, the bag and filter can be cleaned regularly or periodically. The bag can be regenerated by washing, and the filter can be shaken off by compressed air blowing back or gently tapping with hands.

AfterSalesService :

• Single machine pulse dust removal equipment