JL/G1A-400/35 wholesale and retail high zinc layer steel core aluminum stranded wire

Description :

　　JL/G1A-400/35 wholesale and retail high zinc layer steel core aluminum stranded wire

　　Characteristics of steel cored aluminum stranded wire;

　　Aluminum conductor steel reinforced, ACSR. It is a reinforced conductor with single or multiple layers of aluminum stranded wires twisted outside a galvanized steel core wire. Mainly used in the power and transmission line industries.

　　Specification of Steel cored Aluminum Stranded Wire 10/2~1440/100 Implementation Standard GB/T1179-2017

　　Steel core aluminum stranded wire has a steel core inside and is wrapped around the steel core by twisting aluminum wire outside; Steel core mainly plays a role in increasing strength, while aluminum stranded wire mainly plays a role in transmitting electrical energy.

　　Steel cored aluminum stranded wire has the characteristics of a very simple structure, easy installation, convenient maintenance, low line cost, large transmission capacity, and is also conducive to laying across special geographical conditions such as rivers and valleys. It has good conductivity and sufficient mechanical strength, high tensile strength, and can amplify tower distance. Therefore, it is widely used in overhead transmission and distribution lines of various voltage levels.

　　The models of steel cored aluminum stranded wire are divided into JL/G1A JL/G1B JL/G2A JL/G2B JL/G3A, where G1A or G1B refers to ordinary strength steel wire. G2A or G2B refers to high-strength steel wire. G3A refers to ultra-high strength steel wire.

　　Steel cored aluminum stranded wire is a reinforced conductor in which single or multiple layers of aluminum strands are twisted around a galvanized steel core wire. Mainly used in the power and transmission line industries. Steel cored aluminum stranded wire is made by twisting aluminum wire and steel wire, and is suitable for overhead transmission lines. For high-voltage transmission lines, due to the limited path of the line and the impossibility of installing multiple lines on one path, people have come up with the method of using one path, one set of iron towers, and hanging multiple wires, that is, one line is equivalent to installing multiple lines; For 500KV transmission lines, China mostly adopts the method of hanging four wires, which is called the same tower parallel installation.

　　JL/G1A-400/35 wholesale and retail high zinc layer steel core aluminum stranded wire

　　resistivity

　　If necessary, the resistivity of the single wire should be measured on the selected single wire from the stranded wire. The sample should be manually straightened and measured according to the method specified in GB/T 3048.2-2007. The test results should meet the requirements of the corresponding single wire standard. Except for galvanized steel stranded wire, resistivity measurement is generally not required for all galvanized steel wires.

　　Surface condition

　　The surface of the stranded wire should meet the requirements of 5.3. 6.6.7 Pitch to diameter ratio and twist direction

　　The pitch to diameter ratio of each layer of twisted wire should be the ratio of the measured pitch to the outer diameter of that layer.

　　The measured values should meet the requirements of 5.4. In addition, attention should be paid to the twisting direction of each layer, which should also comply with the requirements of 5.4.

　　packaging

　　During normal loading, unloading, transportation, and storage, wires should be properly packaged to prevent damage.

　　The wires should be delivered in reels, with the distance between the outermost layer and the edge of the cable reel side panel not less than 30 mm, and properly packaged. The two wires connected together should have at least half of the single wire cut at a distance of not less than 15 cm from the connection point, and the fracture should be tightly tied.

　　The delivery tray shall comply with the provisions of JB/T 8137-2013 (all parts), or may be agreed upon by the supply and demand parties through mutual agreement. Short section wires are allowed to be delivered in loops, and each loop should be tied at least three times and properly packaged.

　　Each coil or circle of wire should be labeled with:

　　Each coil or turn of wire should be labeled with the following information:

　　Manufacturer name, manufacturer serial number (if any); b) Wire model, nominal cross-section, and number of single wires;

　　GB/T 1179—2017

　　Shipping, rotation direction, or line marking; The marking that the spool cannot be placed flat during transportation; The length, gross weight, and net weight of each wire from outside to inside, in kilograms;

　　Manufacturing date: Year/Month;

　　Steel cored aluminum stranded wire should be delivered in reels, with the distance between the outermost layer and the edge of the cable reel side panel not less than 30mm, and properly packaged. The two twisted wires connected together during packaging should have at least half of the aluminum wire cut at the connection point, and the two sides of the connection point should be firmly tied. The cable reel shall comply with the provisions of GB4005-83 "Delivery reels for wires and cables". Short stranded wires are allowed to be delivered in loops, and each loop should be tied at least three times and properly packaged. The product should be inspected and qualified by the manufacturer before leaving the factory, and each product leaving the factory should be accompanied by a quality inspection certificate.

　　Steel cored aluminum stranded wires are arranged in a criss crossing manner on transportation vehicles such as vehicles and ships. The cable reels must be placed steadily, and both sides must be firmly fixed to the transportation vehicle with steel wire ropes. The bottom of the cable reels should be plugged with triangular wedges to prevent them from shaking, colliding, or tipping over during transportation. When transporting large cable reels, attention should be paid to selecting road transportation equipment. If using heavy-duty trucks for transportation, the height of the truck should comply with the height restrictions of bridges, culverts, etc. on the traffic road. If the limit is exceeded, a dedicated trailer can be used to reduce the transportation height. When the cable reel rolls on the ground, it must be rolled in the direction indicated by the arrow on the side of the cable reel. Rolling in the opposite direction will cause the cable to unwind and loosen. For cables without protective plates, the two side plates must protrude more than 10cm from the outer layer of the cable when rolling. During rolling, hard objects should be prevented from pressing under the cable reel to avoid damaging the cable. When rolling the cable reel, it should be controlled within a small distance range, and special equipment such as forklifts or cranes should be used for long-distance movement.

AfterSalesService :

• aluminum conductor steel reinforced (ACSR)