Metal stamping parts cleaning machine, automotive parts ultrasonic degreasing and cleaning line

Description :

　　Metal stamping parts cleaning machine, automotive parts ultrasonic degreasing and cleaning line

　　The metal stamping parts cleaning machine and the ultrasonic oil removal cleaning line for automotive parts use a unique stainless steel chain transmission cleaning, which is beautiful and elegant. The perfect combination of high-pressure spraying and ultrasonic cleaning results in excellent cleaning effects; Remove cutting grease, dirt, and metal pins attached to the surface of metal stamping parts, with consistent cleanliness and no damage to the surface. Without the need for manual contact with cleaning solution, it is safe and reliable to clean the debris, fine seams, and concealed parts of hardware after drilling deep hole screw holes. The spatial layout of each part is reasonable, with maintenance channels left, and the appearance is simple and beautiful.

　　Characteristics of ultrasonic degreasing and cleaning line for automotive parts with metal stamping parts cleaning machine:

　　1. Metal stamping parts cleaning machine, ultrasonic degreasing and cleaning line for automotive parts. The internal stainless steel structure, inner groove and vibration plate are made of stainless steel, which is more corrosion-resistant. Fully enclosed and leak proof design to prevent cleaning solution from overflowing.

　　2. The continuously variable speed transmission system has low noise and smooth operation, making it easier to operate. The workpiece transfer speed can be adjusted as needed at any time.

　　3. Set up an automatic constant temperature device for solvent heating, with a temperature control range of room temperature -95 ℃ and a working range of room temperature -60 ℃; Set the cleaning temperature as needed; This device also reserves a solar heating interface, which is more energy-efficient and environmentally friendly. The heating and drying system automatically maintains a constant temperature, with a temperature control range of room temperature to 200 ℃. Set up over temperature and liquid shortage alarm functions.

　　4. The oil-water separation device and precision filtration system can keep the cleaning solution clean for a long time and reduce cleaning costs. The independent exhaust device and condensation system reduce the steam concentration in the cleaning area, avoiding secondary pollution of the workpiece.

　　5. The ultrasonic cleaning vibrating plate and the body adopt a separate structure, which is easy to maintain and repair. Adopting an independent electrical control cabinet design, it is easy to operate and safer. Reserved space and interfaces in the cabinet for functional upgrades and connection with other production lines.

　　6. The metal stamping parts cleaning machine and automotive parts ultrasonic degreasing cleaning line use water-based solvents, reducing the amount of cleaning agents used and making it more environmentally friendly.

　　Advantages of ultrasonic degreasing and cleaning line for automotive parts with metal stamping parts cleaning machine:

　　Reduce labor intensity: manual cleaning: harsh cleaning environment, heavy physical labor, complex mechanical parts require long cleaning time. Ultrasonic cleaning: low labor intensity, clean and orderly cleaning environment, automatic and efficient cleaning of complex parts.

　　Environmental protection and energy conservation: The ultrasonic cleaning system is equipped with a circulating filtration system, which can achieve the cyclic filtration and repeated use of cleaning solvents, which is of great significance for saving water resources, cleaning solvent costs, and improving the environmental image of enterprises.

　　Instructions for using ultrasonic cleaning machine:

　　oneInstallation of Ultrasonic Cleaning Machine:

　　Please refer to the installation manual of the ultrasonic cleaning machine to connect the temperature control sensor signal line, ultrasonic drive line, heater control line and other circuits between the electrical control cabinet of the cleaning machine and the host, and connect the 380VAC power supply. Install the water inlet pipe, water outlet pipe and overflow discharge pipe of the cleaning machine.

　　twoUltrasonic cleaning machine with water:

　　Add an appropriate amount of clean water to the cleaning tank, with the liquid level reaching a height that submerges the parts to be cleaned, generally not exceeding three-quarters of the cleaning tank.

　　threeUltrasonic cleaning machine heating:

　　Activate the electric heating switch and point the white scale on the water temperature adjustment knob to the appropriate temperature (around 60 ℃). The temperature of the cleaning machine should not exceed 70 ℃ during use.

　　fourUltrasonic cleaning machine with cleaning agent added:

　　When the water temperature rises to around 40 ℃, add UC-O3 component cleaning agent to the cleaning tank (usually around 5kg at a time), slowly stir the clean water to fully dissolve it (at this time, you can also start the ultrasonic wave or turn on the air blowing device for stirring).

　　fiveUltrasonic cleaning machine pretreatment:

　　Before cleaning, it is advisable to use a bamboo knife to briefly clean the dirt on the surface of the components (such as dust on the outer surface of the dust cover, and thick and easily removable oil sludge on the curved surface of the cylinder block), in order to extend the service life of the cleaning solution.

　　Ultrasonic waves can perform precise cleaning, but their ability to treat mud like pollutants is weak. Therefore, in pre-treatment, efforts should be made to remove yellow or thin mud like pollutants as much as possible.

AfterSalesService :

• Metal stamping parts cleaning machine