Vortex high-pressure fan

Description :

　　Vortex high-pressure fan Vacuum vortex high-pressure blower, wear-resistant high-pressure blower, dual-purpose high-pressure blower for blowing and suction

　　Wear resistant high-pressure blowerFeatures:

　　1. Easy to install

　　Air ring vacuum pump is different from general vacuum pumps, and can be installed at any time in the place of use for compressed air or for evacuation. And it can be installed in any horizontal or vertical direction.

　　2. Sturdy structure

　　The body is made of ADC12 aluminum alloy casting, which is different from general iron shell or AC10 aluminum alloy blowers. ADC12 material is the same as the wheel drum material, making it more sturdy and durable.

　　3. High reliability

　　Apart from the impeller, there are no other moving parts, and the impeller is directly connected to the motor without gears or transmission belts, making it highly reliable and almost maintenance free. No oil and gas, no pollution. When the impeller rotates, it does not come into contact with anything and is free of lubrication, so it can be oil-free.

　　4. Low vibration

　　Vortex high-pressure fanUse and maintenance

　　1. The air pump should be placed in a relatively stable place, and the surrounding environment should be clean, dry, and well ventilated.

　　2. The rotation direction of the air pump impeller must be in the direction indicated by the arrow on the fan casing.

　　3. When the air pump is working, it should be avoided that the inlet and outlet of the fan are completely sealed to prevent excessive heat generation and motor overcurrent that may cause damage to the air pump.

　　4. Except for the two bearings of the motor rotor, there is no direct contact friction in other parts of the air pump. The installation method of bearings for this air pump is mainly divided into two categories. *The bearing at the end of the class air pump is installed in the pump body between the motor base and the impeller, and this type of air pump does not need to be lubricated normally. The bearings on the second type of air pump end are installed in the middle of the pump cover, and the bearings on this type of air pump end should be lubricated regularly. Once a month, for air pumps that work continuously in three shifts, the refueling frequency should be increased. The maintenance and upkeep of the bearings on the motor and fan end of this type of air pump shall be in accordance with the * type of air pump.

　　5. The filter screens and silencers at both ends of the inlet and outlet should be cleaned in a timely manner according to the situation to avoid blockage and affect use.

　　6. The external connection of the inlet and outlet must be made using flexible hoses (such as rubber hoses or plastic spring hoses).

　　7. Bearing replacement: Bearing replacement must be carried out by personnel familiar with repair work. First loosen the screws on the pump cover, and then disassemble the parts one by one according to the order shown in the diagram. The disassembled parts should be cleaned, and then assembled in reverse order. When disassembling, do not forcefully pry the impeller. Use a dedicated roller to remove it, and do not miss the adjusting gasket to avoid affecting the clearance that has been adjusted before leaving the factory.

　　8. It is strictly prohibited for solids, liquids, and corrosive gases to enter the pump body.

　　Dual purpose high-pressure blower for blowing and suctionInstallation precautions:

　　1. Installation location: It must be installed indoors in a place that is not affected by wind and rain

　　2. Environmental temperature: below 40 ℃

　　3. Relative humidity: below 80%

　　4. Air quality: If there are corrosive or flammable gases such as acids and alkalis in the air, they should not be transported by high-pressure blowers to avoid danger

　　5. Dust protection: Avoid using in places with large amounts of dust, powder, or fibers. If it is necessary to use in such places, please install a filter and regularly clean the dust attached to the filter and inside the high-pressure blower

　　6. Ventilation and heat dissipation: Please choose to use it in a well ventilated place and not in a sealed room or box

　　7. Storage space for vortex fans: For the convenience of maintenance or repair, please avoid installing in overly narrow areas

　　8. Avoid vibration: Please install in a vibration free location; If the vibration in the venue is unavoidable, anti vibration measures must be installed to prevent the high-pressure blower from being damaged by external vibrations.

AfterSalesService :

• Vortex high-pressure fan