Steel skeleton lightweight plate suitable for Inner Mongolia coal transportation wharf 3012

Description :

　　Steel skeleton lightweight slab Inner Mongolia wharf adopts 3012-1

　　Thermal insulation: Steel skeleton lightweight panels have excellent thermal insulation performance, with low thermal conductivity and a low overall heat transfer coefficient of up to 0.3w/m2k, meeting the energy-saving requirements of building insulation in high-altitude regions; The board has excellent thermal insulation performance. When the outer side of the board is heated to 900 ℃, the temperature inside the board is only 50 ℃, making it an ideal building insulation material in high-temperature areas.

　　Sound insulation: The average sound insulation of steel frame lightweight panels is above 43db, meeting the sound insulation requirements of high-grade acoustic buildings such as studios. 6. Seismic resistance: The steel skeleton wharf slab is a lightweight plate that is conducive to seismic resistance. With reasonable seismic node design, it can meet the seismic fortification intensity requirements of 8 degrees. And during an earthquake, the secondary damage caused by the sheet metal is minimal, making it an ideal component material for buildings in earthquake prone areas.

　　The loft partition floor adopts new materials and formulas to develop a new type of sandwich floor, which solves the defects of easy bending and deformation, easy water absorption and expansion, easy delamination in the original product. It has higher strength, lower wet expansion rate, stronger impact resistance, higher bearing capacity, and is safer.

　　Scope of use for loft floor slabs

　　The product is mainly suitable for building floors such as coal conveyor bridges, industrial plants, office and commercial buildings, and residential loft mezzanines.

　　Steel skeleton lightweight plate is made of hot-dip galvanized lightweight steel frame, ribs, and cold drawn low-carbon steel wire mesh; Foamed concrete, expanded perlite, cellulose fiber, crack resistant active reinforcement agent; Composed of fiberglass, wear-resistant, anti-seepage, waterproof, and crack resistant mortar structure, using a unique technique and formula, and poured in layers.

　　Laying out: After the handover with the previous process is completed, according to the layout diagram, lay out the position of the board edge and check whether the layout intersects with the on-site structure.

　　At present, most of the new building materials enterprises in China produce mid to low end products, and energy-saving and emission reducing products are rarely asked about. In order to promote the transformation of scientific and technological achievements and promote building energy conservation work, the Ministry of Housing and Urban Rural Development and the Ministry of Science and Technology recently jointly issued the "Catalogue for Promoting Energy saving Renovation Technologies of Existing Buildings", which includes multiple building materials products. This also includes new insulation materials such as cement foam board. Steel skeleton lightweight board is superior to other lightweight asbestos products and other insulation materials. It is used for roof insulation and exterior wall insulation, replacing other insulation materials such as polyethylene (board). It has good insulation, thermal insulation, sound insulation, light load-bearing and other properties, and is easy to operate, highly mechanized, time-saving and labor-saving. Mechanical vertical pipeline transportation can be used during construction, which shortens working hours and can improve work efficiency by 6-10 times compared to other methods.

　　When installing steel frame lightweight panels, the length of the panel that should be placed on the support should not be less than 60 millimeters. After being in place, the main ribs of the roof panel and floor slab should be welded firmly to the support, and the length of the welding joint should not be less than 60 millimeters. The height of the welding joint should be 4 millimeters, and three-point welding should be ensured. For roof panels and floor slabs with seismic fortification requirements, they should be strengthened according to the connection node method in the standard. For the installation of steel skeleton lightweight roof panels, it is advisable to use structural sloping for the roof, with a slope of no less than 2%. The waterproof layer can be directly applied to the roof panel.

　　Before construction, the main structure should be measured, and the allowable deviation of the main structure is required to be ± 10 millimeters in the vertical direction and ± 25 millimeters in the horizontal direction. If the deviation is too large, a treatment plan should be agreed upon with the relevant construction unit. Shandong Steel Skeleton Lightweight Plate Manufacturer

　　For the construction of steel frame lightweight wall panels, various preparations should be made before construction, including the preparation of connectors and supporting materials, and the setting out of horizontal and height control lines. Lightweight wall panels should be positioned according to the number, and attention should be paid to the installation sequence. After aligning the wall panels, temporary fixing should be done first, and then the hooks should be removed, and then fixed according to the connection method in the relevant architectural drawings.

AfterSalesService :

• Steel skeleton lightweight plate