Automotive Aerospace LCP 6244L DuPont 40% Fiberglass Reinforced Automotive Electronics, Electrical and Aerospace

Description :

　　LCP 6244L DuPont, USA

　　Zenite 6244L is a lubricating 40% glass fiber and mineral reinforced liquid crystal polymer resin. It is highly suitable for use in the automotive, electrical/electronics, telecommunications, and aerospace industries. Information provided by Seranis Company.

　　6244L LCP, 40% Mineral/Glass Reinforced Physical Properties Table

　　Physical performance rating (metric) rating (imperial) testing method

　　Density 1.73 g/cc 0.0625 lb/in3 ISO 1183

　　Saturated water absorption rate 0.020% 0.020% ISO 62

　　Linear molding shrinkage rate, Flow 0.0010 cm/cm 0.0010 in/in ISO 294-4

　　Linear molding shrinkage rate, transverse 0.0040 cm/cm 0.0040 in/in ISO 294-4

　　Mechanical performance rating (metric) rating (imperial) testing method

　　Tensile strength (fracture) 112 MPa 16200 psi 5mm/min; ISO 527-2/1A

　　Elongation (fracture) 1.5% 1.5% 5mm/min; ISO 527-2/1A

　　Tensile modulus 13.1 GPa 1900 ksi 1mm/min; ISO 527-2/1A

　　Bending strength 163 MPa 23600 psi ISO 178

　　Bending modulus 13.2 GPa 1910 ksi ISO 178

　　Suspended wall beam notch impact strength 7.00 kJ/m2 3.33 ft lb/in2 ISO 180/1A

　　Suspended wall beam without notch impact strength 20.0 kJ/ m2@Temperature 23.0 °C 9.52 ft-lb/ in2@Temperature 73.4 °F ISO 180/1U

　　Electrical performance rating (metric) rating (imperial) testing method

　　Volume resistivity>=1.00e+14 ohm cm>; = 1.00e+14 ohm-cm IEC 60093

　　Surface resistance>=1.00e+15 ohm>; = 1.00e+15 ohm IEC 60093

　　dielectric constant 3.6@Frequency 1.00e+6 Hz 3.6@Frequency 1.00e+6 Hz IEC 60250

　　4.4@Frequency 100 Hz 4.4@Frequency 100 Hz IEC 60250

　　Dielectric strength 34.0 kV/mm 864 kV/in IEC 60243-1

　　Dissipation factor 0.013@Frequency 100 Hz 0.013@Frequency 100 Hz IEC 60250

　　0.023@Frequency 1.00e+6 Hz 0.023@Frequency 1.00e+6 Hz IEC 60250

　　Thermal performance rating (metric) rating (imperial) testing method

　　Linear coefficient of thermal expansion - Flow 6.00 μ m/m - ° C 3.33 μ in/in - ° F ISO 11359-2

　　Linear coefficient of thermal expansion, transverse flow 50.0 μ m/m - ° C 27.8 μ in/in - ° F ISO 11359-2

　　Hot deformation temperature under load (1.8 MPa) 269 ° C 516 ° F ISO 75-1, -2

　　Flammability (UL94) V-0@Thickness 1.50 mm V-0@Thickness 0.0591 in

　　Processing performance rating (metric) rating (imperial) testing method

　　Processing temperature 40.0-150 ° C 104-302 ° F cavity

　　Processing (melt) temperature 350-360 ° C 662-680 ° F

　　Drying temperature 150 ° C 302 ° F

　　Drying time 3 hours 3 hours

　　Moisture content 0.010% 0.010% Necessary low maximum

AfterSalesService :

• Automotive Aerospace LCP