High pressure fan, blower, vortex fan, air pump, vortex air pump, Roots blower, industrial high-power

Description :

High pressure fan, blower, vortex fan, air pump, vortex air pump, Roots blower, industrial high-power

Vortex fan - Vortex fanAdvantages:

　　Vortex blowers can be divided into single impeller, double impeller, and three impeller fans. As the name suggests, they are defined by the number of built-in impellers. At the same power:

　　Pressure: single blade

　　Flow rate: single blade

　　Weight and volume: single blade

　　Price: Single blade

　　1. Dual function of blowing and suction, one machine can be used for vacuum adsorption, blowing and conveying, as well as closed circuit air circulation, etc.

　　2. Oil free operation, the output air is clean, because the fan relies on the input of electricity to operate, and there are no oily components inside, so there is no need to worry about air pollution during transportation, and no impurities will be produced.

　　3. High pressure and power, compared to centrifugal fans and medium pressure fans, its pressure is much higher, which determines the pressure problem that other fans cannot meet. Moreover, it has a small size, low sound, and will not cause noise pollution.

　　4. The pump body is integrally cast using a hydraulic press and equipped with shockproof mounting feet. Therefore, its requirements for the installation foundation are also very low, and it can even operate normally without fixing the feet.

Low noise vortex air pumpCapable of functions:

1. It has dual functions of blowing and suction, and can be used for both suction and blowing;

2. The fan has a small size, light weight, low noise, and the air output from the air source is clean without water or oil;

3. Exhaust and supply fans are divided into:; Pneumatic conveying and pipeline conveying;

4. Eight characteristics can be modified: (vertical, horizontal, heat-insulating, DC, explosion-proof, anti-corrosion, waterproof, belt drive);

5. The shell is die cast as a whole and uses shockproof mounting feet, so its requirements for the installation foundation are also very low. It can even operate normally without fixing the feet, which is very convenient and saves installation costs and installation cycles;

6. The fan blades that generate centrifugal force are made of double-sided forward leaning multi blade, molded in one go, computer-controlled dynamic balance, extremely low vibration, stable wind force, low noise, and can withstand certain frictional impact forces, with a long service life.

7. The drainage side panel has a built-in side suction port, which, when combined with the fan blades, can generate a large negative pressure suction force, making the self-priming feeding more stable.

RB-81D-2 high-pressure vortex fan, vortex high-pressure blower, vortex vacuum suction fanDetection method:

1. Check the fastening condition of each part and whether there is any looseness in the positioning pin

2. There is no oil leakage inside the blower body

3. There should be no scaling, rusting, or peeling inside the blower body

4. Pay attention to whether the lubrication and heat dissipation are normal, pay attention to the quality of the lubricating oil, regularly listen to the operation of the blower for any noise, pay attention to whether the unit is running under non compliant working conditions, and regularly add butter

5. The overload of the blower is sometimes not immediately displayed, so attention should be paid to the increasing trend of the intake and exhaust pressure, bearing temperature, and motor current to determine whether the machine is running normally

6. Before disassembling the machine, the dimensions of each fitting should be measured, recorded, and marked on the components,

7. The oil tank of a new or overhauled blower should be cleaned and put into operation according to the usage steps. It is recommended to replace all lubricating oil after 8 hours of operation

8. A reasonable maintenance system should be formulated based on specific usage conditions, carried out on schedule, and recorded. It is recommended to conduct a major overhaul once a year and replace bearings and related vulnerable parts

9. It is recommended that the blower be overhauled by maintenance personnel

High pressure fan, blower, vortex fan, air pump, vortex air pump, Roots blower, industrial high-power

AfterSalesService :

• High pressure fan blower